JL AUDIO M6-770X-C-GwGw marine zvučnici, par
Part Nr 93728
M6 7,7-inčni morski koaksijalni zvučnici (100 W, 4 Ω) - sjajni bijeli ukrasni prsten, sjajna bijela klasična rešetka
Namjenski projektirani i izrađeni za stvarne pomorske dužnosti, M6 koaksijalni sustavi pružaju maksimalne zvučne performanse u bilo kojem otvorenom čamcu.
Predimenzionirani 7,7-inčni dizajn koaksijalnog M6-770X rezultira povećanom učinkovitošću (veći izlaz za datu količinu snage). Kombinirajte tu prednost s dugim izletom i izvrsnim upravljanjem snagom i dobit ćete sustav zvučnika uistinu sposoban za brzu i jasnu reprodukciju u motornom čamcu.
Visokotonski visokotonac od čistog svile od 1 inča, posebno obrađen da izdrži morski okoliš, podnosi visoke frekvencije. Cijenit ćete čisti, zglobni visokofrekventni odziv M6 kupolastog visokotonca, posebno pri većim razinama glasnoće.
Višenamjenski, istinski dvosmjerni pasivni crossover skriven je u okviru woofera, zaštićen od vibracija i korozije. Uključen je i automatski, čvrsti krug zaštite visokotonca kako bi se minimalizirala mogućnost kvara visokotonca.
Iako se koaksijalni sustavi M6-770X mogu koristiti sa samo 40 W po kanalu, za najbolje audio performanse preporučujemo pojačala s kontinuiranom snagom između 40-200 W po kanalu.
Prodaje se u paru.
.............................................................................................................................................
M6 7.7-inch Marine Coaxial Speakers (100 W, 4 Ω) - Gloss White Trim Ring, Gloss White Classic Grille
Purpose-engineered and built for real marine duty, M6 coaxial systems deliver maximum audio performance in any open-air boating environment.
The oversized 7.7-inch design of the M6-770X coaxial results in increased efficiency (more output for a given amount of power). Combine that advantage with long excursion and excellent power handling and you have a speaker system truly capable of playing loud and clear in a powerboat at speed.
A 1-inch pure silk dome tweeter, specially treated to withstand the marine environment, handles the high-frequency duties. You will appreciate the clean, articulate high-frequency response of the M6 dome tweeter, especially at higher volume levels.
A multi-order, true 2-way passive crossover is concealed within the woofer chassis, shielded from vibration and corrosion. Also included, is an automatic, solid-state tweeter protection circuit to minimize the possibility of tweeter failure.
Although M6-770X Coaxial Systems can be used with as little as 40 W per channel, for best audio performance we recommend amplifiers capable of between 40-200 W of continuous power per channel.
Sold as a pair.
JL AUDIO M6-770X-C-GwGw marine zvučnici, par
Part Nr 93728
Specifications
|
Continuous Power Handling (RMS)
|
100 W
|
|
Peak Music Power
|
250 W
|
|
Recommended Amplifier Power (RMS)
|
40 - 200 W / Ch.
|
|
System Efficiency
|
91.0 dB @ 1 W / 1 m
|
|
System Nominal Impedance
|
4 Ω
|
|
System Frequency Response
|
45 Hz - 25 KHz ± 3 dB
|
Physical Specifications
|
Frame Outer Diameter (A)
|
7.70 in / 196 mm
|
|
Bolt Hole Circle Diameter (B)
|
6.92 in / 176 mm
|
|
Frontal Grille Protrusion (C)
|
1.03 in / 26 mm
|
|
Mounting Hole Diameter (D)
|
6.25 / 159 mm
|
|
Mounting Depth (E)
|
3.32 in. / 84 mm
|
Dynamic Motor Analysis - DMA Optimized Motor
Summary:
JL Audio's proprietary Dynamic Motor Analysis system is a powerful suite of FEA-based modeling systems, first developed by JL Audio in 1997 and refined over the years to scientifically address the issue of speaker motor linearity. This leads to vastly reduced distortion and faithfully reproduced transients... or put simply: tight, clean, articulate bass.
Detailed Information:
Since 1997, JL Audio has been at the forefront of Finite Element Analysis-based modeling of loudspeaker motors and suspensions. This research is aimed at decoding what we refer to as the "Loudspeaker Genome"... a project aimed at understanding the true behavior of loudspeakers under power and in motion. A major component of this integrated system is DMA (Dynamic Motor Analysis). Starting with the 15W3 and the W7 Subwoofers in the late 1990's and early 2000's, DMA has played an important role in the design of all JL Audio woofers sold today, including our component woofers.
DMA is a Finite Element Analysis (FEA)-based system, meaning that it takes a large, complex problem, breaks it down into small solution elements for analysis and then assembles the data to form an accurate, "big-picture" solution. DMA's breakthrough is that it actually considers the effects of power through the coil as well as coil/cone position within the framework of a time-domain analysis. This gives us a highly accurate model of a speaker's actual behavior under real power, something that the traditional Thiele-Small models or other low power measurements cannot do. Because DMA does not rely on a steady-state model, it is able to consider shifts in the circuit elements being analyzed. These modeling routines are intense, requiring hours to run for a whole speaker.
DMA is able to analyze the real effects of fluctuating power and excursion upon the magnetic circuit of the motor, specifically the dynamic variations of the "fixed" magnetic field. This delivers intensely valuable information compared to traditional modeling, which assumes that the "fixed" field produced in the air gap by the magnet and the motor plates is unchanging. DMA not only shows that this "fixed" field changes in reaction to the magnetic field created by current flowing through the voice coil, but it helps our engineers arrive at motor solutions that minimize this instability. Analyzing this behavior is critical to understanding the distortion mechanisms of a speaker motor and sheds light on the aspects of motor design that determine truly linear behavior:
- Linear motor force over the speaker's operational excursion range
- Consistent motor force with both positive and negative current through the coil
- Consistent motor force at varying applied power levels
Our ability to fully analyze these aspects of motor behavior allows our transducer engineers to make critical adjustments to motor designs that result in extremely linear, highly stable dynamic loudspeaker motor systems.
The payoff is reduced distortion, improved transient performance and stellar sound quality.
Marine Materials / Testing
Summary:
The design of marine products requires extensive materials testing to achieve reliability and longevity.
Detailed Information:
Building serious marine products requires a real commitment to environmental testing and materials specification. To this end, JL Audio has invested in Ultraviolet testing chambers (to simulate years of sun exposure) and Salt Fog chambers (to simulate years of exposure to salt-water environments). This testing is critical to building products that will not only sound great in your boat, but will also sound great for many, many years.
Materials Used:
- injection-molded mica-filled polypropylene cone bodies with synthetic rubber surrounds, specifically formulated with UV inhibitors for marine duty.
- Marine-grade, synthetic fiber spiders with progressive roll designs to withstand high humidity.
- Specifically engineered polymer baskets are corrosion and UV-resistant and encapsulate the woofer's motor system to prevent corrosion.
- Gold-plated, marine-grade brass connection terminals
- Marine-grade stainless steel mounting hardware is included.
Built in U.S.A. with Global Components
Summary:
JL Audio's Miramar, Florida loudspeaker production facility is one of the most advanced in the world.
Detailed Information:
At a time when most audio products are built overseas, JL Audio’s commitment to in-house loudspeaker production continues to grow. To pull this off in a competitive world market, our production engineering team has created one of the world’s most advanced loudspeaker assembly facilities and established a global network of quality component suppliers who build to our specifications. This, combined with our commitment to state-of-the-art assembly technology, allows our skilled workforce to efficiently build JL Audio products to extremely high quality standards, right here in the U.S.A.
Since most of our premium loudspeakers incorporate proprietary, patented technologies requiring specific assembly techniques, we find it is vital that the people who designed them have close access to the people manufacturing them. The following JL Audio products are built in our Miramar, Florida factory, with global components:
- Subwoofers: W7, W6v3, TW5v2, TW3, TW1, W3v3
- Enclosed Car Subwoofers: Stealthbox®, PowerWedge™, ProWedge™, H.O. Wedge™ & MicroSub™ Enclosed Subwoofers
- Marine Loudspeakers, Marine Subwoofers and Marine Enclosed Loudspeakers
- Home Subwoofers: Dominion™, E-Sub, Fathom® and Gotham®
